So in this situation vacuuming to waste is the best solution to remove the algae dust from the pool after it has been killed using shock treatment. Disconnect the drain plug and install a 1.5 hose adapter and backwash hose with a clamp. How To Vacuum To Waste With Cartridge Filter, When using a cartridge filter in your swimming pool, the debris that you scoop out of the. You'll have to stop the system, purge the excess pressure, and open the tank according to the manufacturer's instructions. Step 4. The way you vacuum a pool to waste will depend on what kind of filter valve you have; a multiport valve, push-pull valve, or you may not have one at all. Create an account to follow your favorite communities and start taking part in conversations. When using multiport valves, set the handle to Waste or Drain according to the valve type. Turn your pump back on and now you are draining. This way the dirt that is picked up by the vacuum does not get trapped in the filter, clogging the filter medium or even returning to the swimming pool, but is ejected from the system completely. Any other ways to do it? You can buy roll up backwash hoses quite cheaply on Amazon. You can also buy heavy duty, firehose type of hose, in 2 diameter, that will last much longer. Expel the air from the vacuum hose and connect to the skimmer port after removing the skimmer basket. How do you use the waste setting on a sand filter? Can I use a regular garden hose as a backwash hose? Stay up-to-date with the latest safety info, regulation changes and special offers. You should just be able to put a vac hose in the skimmer and vac with the pump running. If your pool system does not expel the water down a drain then it will run out into your yard somewhere via the waste line.

If your swimming pool has a feature that allows it to run the filter in a 'waste' mode, you'd be wise to understand this function. Make sure to empty all skimmer baskets. I was recommended Swim Universitys Pool Care Handbook and video course so I bought it and have never regretted it. The grids will filter it on filter, but if you pull the grids and set the valve to backwash, this will basically be a vac to waste. Goodbye winter debris! Flocculant will normally leave debris on the bottom of your pool so vacuuming to waste will prevent this debris clogging the filter, as would happen if vacuuming on the filter setting. It would seem that there is no way to vacuum to waste a sand filter or is there?

You're likely to find a layer of sediment and sludge on the bottom. When you vacuum using the waste setting the pool water will be expelled, without returning to the pool, so the pool level will drop. Turn off the pump and screw the plug into the drain plug. This is a really useful tool for getting into the areas that a standard vacuum head simply cannot reach. Connecting the vacuum system to the pump. After the hose fills with water, backwash your sand filter for 2 3 minutes, or until water runs clear. Just open the drain on the back of the filter and the majority of the water will go out the drain. Your pool's filter system starts by sucking the water into a drain or skimmer when it's in regular operation. Step 6. Sometimes, the multiport may have a setting to recirculate the water. In normal mode, the valve will pass water through to the pipe leading to the filter. If you find yourself in the company of those that have to winterize their pools, you know well that when you open it up in the Spring, it looks a lot like a hurricane meets a tornado meets a Mississippi bog. However it is possible to fit a Hayward 3 way valve to bypass the filter and if you do that you will then have the facility to vacuum to waste. The pump pushes the water directly into the filter valve, bypassing the filter sand, grids, or cartridges. If you vacuum to waste, you are bypassing the filter all together and you dont run the risk of the algae bypassing your filtration and/or sanitation system and kicking back out into your pool.

The best example of this is when you first open a pool for swimming season. Fill your pool with water before you begin and run the pipe while vacuuming. You may need help to pull apart the pump and filter slightly as you glue the new valve into place. Add water to the pool if necessary to return it to normal level. It's far better to set your valve to waste, bypass the filter tank, and send the dirty water to a remote part of your property or a nearby drain. pic.twitter.com/hoUGFyvLjJ, Goodbye Winter, hello Summer! Strictly Necessary Cookie should be enabled at all times so that we can save your preferences for cookie settings.

Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful. You will have to top the pool up afterwards. There are not very many times you have to remember how to vacuum to waste because they are few and far between. If you find yourself with an algae problem mid-season, because you finally took that driving vacation to the Grand Canyon that you have always dreamed of, you may have some work on your hands when you get home. Find the drain plug on the back of your filter and unscrew it. How often should you vacuum your above ground pool? Bypassing the filter tank can spare it from a dirty vacuum. This prevents the filter becoming clogged and fine particles going back into the pool. What Is the Setting on a Filter to Vacuum a Pool? As an Amazon Associate I earn from qualifying purchases. I normally check the chemical levels at this stage and add anything necessary to bring the levels to the correct reading. The grids will catch it. Once you have finished vacuuming, turn off your pump. Once you have done that you leave the main drain valve open all the way. Adjust your skimmer and main drain valves for maximum suction through the skimmer, and voila! This position also bypasses the tank but sends the water back to the pool, not out to waste.

If you vacuumed on waste, you will need to turn your filter to the rinse setting, turn on the pump and let it run for about 30 seconds, and then turn the pump back off. Turn the valve whenever you want to vacuum to waste on a cartridge pool filter, or when you need to lower the water from too much rain. Is this a good setup to get the dead algae from the bottom of my pool? Almost. Cartridge filters don't need backwashing, so there usually isn't a valve between the pump and the tank. Attach one of the hose's ends to hole on the top of the. Roll out the backwash hose if you have one, and begin vacuuming as fast as you can manage. A filter to waste arrangement allows the water separated in the filtration cycle to be disposed of or made usable again after it washes back. If you want to keep the water clear, open your pool early in the season to avoid the Spring algae blues. When your turn the pump back on, you should see bubbles coming out of the pool returns indicating that you are in the FILTER mode or the RECIRCULATION mode. Hopefully you have it plumbed to go somewhere. So you just need to remove the vacuum head and vacuum hose from the pool, clear up and put the pump back on after putting the multiport valve back into the Filter position. Once the vacuuming finishes, remove it from the pool and detach the hoses. What is the waste function on my pool filter? There are quite a few different ways to use the waste valve. The concern of how to vacuum to waste with a cartridge filter arises frequently and results in many confusing answers. This directs dirty vacuum water through the pool filter to remove the contaminants, then conveys filtered water through return lines back to the pool. There is no doubt that one of the valve modes on a multiport pool filter will have a 1-1/2 waste line built-in. Sure, you can vacuum up the green stuff like you normally would, but the problem is that when the algae gets trapped in your filter, it can cause ongoing filter issues. hb```a``o@ (9:l$ J>o0e|xqIFN"3:q:D+T..p8X6,2 ` Aquatix Pro Pool Step & Corner Vacuum Brush. Every pool owner can utilize the pool waste line for easy and effective pool vacuuming. Shut off pump and switch the multiport valve to the Drain to. Tighten it fully with pliers, anddont stand over the plug, which would be dangerous if it blew out under pressure. This setting is useful for vacuuming the pool and sending large amounts of dirt, organic pollutants such as algae as well as certain chemical pool treatments directly down the drain so they do not contaminate or overload the filter media. Raise the water level in the pool to its highest point without overflowing. This method removes a lot of water from the pool in a short period, so make sure the pool is full before you proceed. If you have a valve that shuts off water to the waste pipe (I have one on my pool set-up) then make sure this is open.

Adjust the multiport faucet by turning off the pump and aligning the multiport faucet with the drain. Even if you have to do a couple of tricks to vacuum to waste, it's usually worth the extra hassle. The best method for pumping to waste on a system that doesn't have the correct valves is to install one. Take off the filter lid, remove the cartridge, and replace it securely, fully tightening the clamp. endstream endobj startxref (Pac-Fab push-pull valves have a reverse operation, up for Filter, down for Backwash). If you have a dirty filter then trying to clean a pool will be much more difficult. You should vacuum to waste if there is a lot of debris in the pool, especially silt, which clogs up the filter quickly, so you need to stop vacuuming and backwash or clean. Vacuum your pool just as you would vacuum your living room, picking up debris or algae as you go. Open the air bleeder and set the push pull in the backwash position. Place the vacuum head into the pool at the deep end, and hold on to the extension pole to stabilize the vacuum head as it sinks to the bottom of the pool. Using the filter setting will save water, but. Connect the pool vacuum hose to the vacuum head (already attached to a pole of course) and lower it into the pool.

Amazon and the Amazon logo are trademarks of Amazon.com, Inc or its affiliates. Disconnect the drain plug and install a 1.5 hose adapter and backwash hose with a clamp. If, like me, you get plenty of leaves at the bottom of your pool then a good leaf rake/net is a must. Use the rinse to clean the pool's side of the filter by sending the water in the same direction as usual, but right across the media and then to waste. Close the pool main drain valve and the valves leading to any skimmers other than the one you will utilize for the pool vacuum source. Pac-Fab 3-way valves are under$30, and the only other materials needed are a bit of pipe and some PVC glue and primer. Then you'll have to open the tank again, reinstall the grids, and resume regular operation. Turn your pump back on and note the lower pressure.

Glue a short piece of pipe to the valve, and clamp a length of backwash hose to the pipe. When the pump is run and you vacuum then the water will come out of this hole. pic.twitter.com/ektkMdMbZ7, Who is ready for swimming season?? Copyrights Protected. So, you have to get creative if you want to run the system to waste. Mate the extension pole with the vacuum head, and attach one end of the vacuum hose to the end of the extension pole. It was probably the best money I spent that year as I have saved thousands by doing it myself. %PDF-1.6 % I think the drain only works when the filter is in backwash mode. That can translate into significant savings for you by reducing the amount of maintenance you need and improving the service life of your filter. Shut off the pump motor and push the T-handle back down into locked position. They are normally too small to be caught by the sand or other filter medium so if vacuumed on the filter setting they will probably just end up being redeposited back into the pool. We hope that you have found this article informative.

to the skimmer that you vacuumed from.

Sitemap 30