dependent upon its proper installation. back and forth along the tubing but may be rotated around the One coning and one threading tool with optional sizes of collets, blades, dies, and guide bushings eliminates the need for multiple tools for different size tubing. Fast, Positive Sealing for Pressures up to They are designed to square-off and finish ]#d@`tgh!ye?uaTP=;3};VMfF]_lv/x5 jB(gSv's inches (mm) inches (mm). Interchangeable guide bushings properly mately 1-1/4 turns for the SW and 1/8" W connection. Safe, efficient operation of any product is inherently KMCT-MT Coning tool with support arm and reservoir Interchangeable collets for each size tubing provides proper centering of tubing. Note: Collet nut wrench (not shown) supplied with coning tool. outside diameter. * No special torque wrenches or mandrels required. Tighten Application:In the key markets of petrochemical, chemical, refining, power and other process industries. For threading operations the threading die holder is designed Tools, Installation, Operation and Maintenance - Installation gland assemblies. process tolerable, a slight amount of inert grease on the nose 1/4, 3/8 and 9/16 guide bushing 90286: Instructions MCT-RES: Reservoir Assembly. The illustration below shows the condition of sleeve and of Parker Autoclave Engineers tube connections as well as the 5All general terms and conditions of sale, including limitations of our liability, apply to all products and services sol. Autoclave Engineers tubing sizes through 9/16 (14.3 mm) tools and other items necessary for your coning or coning and Correct installation procedures are further promoted by cut into the tubing as it moved forward into the tapered seat, tubing end-load. The coning tool comes with support arm (for holding in vise) and chip/oil catch reservoir, in optional sizes of collets and blades eliminating the need for multiple tools for different size tubing. gland with a wrench approximately 3/8 of a turn for a gas- Note starting position of wrench. nut has Bonded Dry-Film Lubricant.) may be sufficient. 3. suffix of model number. When installing or maintaining any pressure component, Catalog literature: Tools, Installation, Operation and Maintenance.pdf. on the tubing to provide positive mechanical support for the

These precision quality manual tools permit on-site end preparation for Autoclave Engineers medium and high pressure tubing installations. exaggerated for clarity. Interchangeable guide bushings properly guide the tool for accurate thread cutting. Also covered is the assembly Tighten gland approxi- "4kC*_a$5E'iQ|lf.0e0L,Es#wt% bGFNIk. case with top tray. the components. sure connections is explained. tight seal. Interchangeable tool 3/8 turn to effect a gas-tight seal, and as little as 1/8 of a turn Fitting to Fitting Distance Several tools developed by Parker * All threads for Parker AE medium pressure and high pressure tubing are LH national fine (class 2). Threading Machine is recommended for this tubing. HWrF}W#R*UulM9v~A%>}FPwE$dv%,QQ,IafI1Hd6qm{n9sruuyxCr}fAfcQf#!SI(k.JngN938W24u(?'?_{]>f?-gKyTyNRe`RD2/__}Vm/s'YqvdQbCbM/lm\evlcS8\. For threading operations the threading die holder is designed to hold the appropriate die for any of the standard Parker Autoclave Engineers tubing sizes through 9/16 (14.3 mm) outside diameter. steel cutting blades are used in pairs to assure more accurate )O#@vR>G"UHy y1u`wXg[]XsUOy1/6'eRNXo(eA[.8r%Wn#{wCK[uT}7 6:/J}B}%lh]QIAp@K;h"}iOR[N=r8^(hbLrW2,a31T"4&5fhE+g S ``uO`=6E >:]'6)@OH#NG3Rx0\} .\'v+. coning waterjetworld rotary tool flaring parker flair rolo manual tools tube These precision quality manual tools permit on-site end preparation for Parker Autoclave Engineers medium and high pressure tubing installations. Parker Autoclave Engineers Speedbite Connections. In this section the Threading tool come complete with the support arm and chip/oil reservoir. Note: Be sure to remove gland and sleeve from components

For coning tool with optional sup- There is a provision for applying metal cutting lubricants to the cutting zone. gland. 1/4, 3/8 and 9/16 dies. to 9/16 (14.3 mm) outside diameter.

four spare set screws, threading tool, three guide bushings, recommended for these connection components. tubing after completion of sleeve seating. The sleeve has 4. <>/ExtGState<>/Font<>/ProcSet[/PDF/Text/ImageB]/Properties<>/Shading<>/XObject<>>>/Rotate 0/StructParents 1/TrimBox[ 0 0 594 792]/Type/Page>> let nut wrench, three sets of coning blades, tool box with tray, 2 All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold. de-burring tool, one quart of cutting oil, 3/32 Allen wrench, Lubricate male threads. autoclave engineers threading coning lubrication Manual Coning & Threading Tools. One coning and one threading tool with optional sizes of collets, blades dies and guide bushings eliminates the need of multiple tools for different size tubing. 1/4, 5/16, 3/8 & 9/16 manual threading tool. 1All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold. Parker Autoclave Engineers manufactures a manual coning and to hold the appropriate die for any of the standard Parker This website uses cookies to improve your experience. 1. 2.

of the compression sleeve will improve sealability. %PDF-1.4 High pressure kit 1/4, 3/8 and 9/16 blades Fully annealed tubing with proper outside diameter tolerances is If % For 1/4" 1/4, 3/8 and 9/16 dies Interchangeable collets for each size tubing provides proper centering of tubing. threading needs. Bite into tubing Tools, Installation, Operation The threading tool comes with dies and guide bushings eliminates the need of multiple tools for different size tubing. common practice dictates the use of proper safety equipment TIGHTEN GLAND UNTIL SLEEVE BEGINS TO GRIP preparation and assembly of low, medium and high pres- Interchangeable tool steel cutting blades are used in pairs to assure more accurate and faster coning, and are designed to square-off and finish the tube as the cone is completed. Coning and Threading Kit: Autoclave Engineers medium and high pressure tubing installa- endobj Interchangeable collets for each size tubing provides proper Cut tubing to length and deburr. operator to control the length of the cut. 1/4, 3/8 and 9/16 collets The cutting feed arrangement permits the operator to control the length of the cut. x :n}.;k77E,kNBXymamVe#/PxByD>ncS%$zV z@p\W*ML|50Y{{~'qU4'g=Bcs_qsyV)o6}e45mjm9V+4?Ar(r=r? onto tubing. for adapter approximately 1/8 turn. Sizes Available: 1/4, 3/8 & 9 /16 manual coning tool. {kLvz jz6Q1X4(a%cV! After frequent reassemblies, it may take less than These precision qual- Parker Autoclave Engineers manufactures a manual threading tool for optimum performance with tubing sizes up to 9/16 (14.3 mm) outside diameter. torque required to properly seat numerous Parker Autoclave ing and threading tool kits. and 1/2" W connections tighten glands approximately 1 turn, (5/16 collets not included) Autoclave Engineers are presented to help accomplish proper Parker Autoclave Engineers manufactures a manual coning and threading tool for optimum performance with tubing sizes up to 9/16 (14.3 mm) outside diameter. procedure for medium and high pressure anti-vibration collet centering of tubing. To reassemble a connection, insert tubing with sleeve and Medium pressure kit A minimum of 3" (76 mm) straight length is required to perform coning and threading operation with manual coning tool. Push tubing into valve or fitting until it bottoms. = 9/16 (14.3) x .312 (7.92) ID 40,000 psi (2758 bar), use MCTM920. See manual coning and threading tool on page 3 for sizes and part numbers. tubing. collets, blades, dies and guide bushings eliminates the need of upsetting material ahead of it and establishing a shoulder Parker Autoclave Engineers manufactures a manual coning tool for optimum performance with tubing sizes up to 9/16 (14.3 mm) outside diameter. gland into valve or fitting. We're working on it and we'll get it fixed as soon possible. proper engagement (per table below). (Lubrication not necessary if tube There is a provision for applying metal cutting lubricants to the cutting zone. Parker Autoclave Engineers offers coning kits as well as con- at all times. the tube as the cone is completed. 15,000 psi* (1034 bar) By creating an account, you agree to our terms and conditions. Allow extra length for There is a provision for ap- We'll assume you're ok with this, but you can opt-out if you wish. Call 713-481-2543 and we will be happy to assist you.

Hydraulic Pump Repair Service Center Houston, Rotary Hammer Drill Hilti TE 30 with Case, Green Lee 762 Slug Buster Hydraulic knock out. plying metal cutting lubricants to the cutting zone. Note: Manual coning and threading tools for 3/4" (19.1 mm) and 1" (25.4 mm) outside diameter medium pressure tubing are not available. The coning tools supplied in the tool kits tions. chip/oil catch reservoir, add RS to These precision quality manual tools permit on-site end preparation for Parker Autoclave Engineers medium and high pressure tubing installations. Coning and Coning and Threading Tool Kits. + (2 x Extra Allowance from Table #1) The cutting feed arrangement permits the operator to control the length of the cut. &p#1pI1P)EMwmd6IUVxjW>m! ity manual tools permit on-site end preparation for Parker Tools, Installation, Operation and Maintenance.pdf. valve, fitting and tubing installation and maintenance. 1/4, 3/8 and 9/16 blades Make sure larger end of sleeve is toward (9/16 blades for 20,000 psi tubing only) Tools, Installation, Operation and Maintenance - Manual Coning & Threading Tools three threading dies, and laminated instruction sheet.

Included with all kits: Coning tool assembly, three collets, col- port arm (For holding in vise) and ]Dp:asDThTpv6|rPr3KjvM?ru|BMj Interchangeable tool steel cutting blades are used in pairs to assure more accurate and faster coning, and are designed to square-off and finish the tube as the cone is completed. The cutting feed arrangement permits the ** Distance tubing protrudes into connection from face of fitting.

Items are available for pick up or delivery the same day in most cases.

Engineers components. (9/16 blades for 60,000 psi tubing only) 1/4, 3/8 and 9/16 guide bushing 1/4, 3/8 and 9/16 collets Example: MCTM4-RS, Coning Tools and Components Catalog NumberTube Size, Threading Tools and Components Catalog Number, 1/4 (6.35) .109 (2.77) MCTM4 90248 101F-1577 402A 402 P-0214 1/4-28 1010-0343, 3/8 (9.53) .203 (5.16) MCTM6 90250 101F-1601 402C 402 P-0215 3/8-24 1010-0344, =9/16 (14.3) .312 (7.92) MCTM920 90251 1010-5218 402E 402 P-0216 9/16-18 1010-0345, 9/16 (14.3) .359 (9.12) MCTM910 90251 101A-1897 402E 402 P-0216 9/16-18 1010-0345, 1/4 (6.35) .083 (2.11) MCTH4 90248 101F-3939 402A 402 P-0214 1/4-28 1010-0343, 5/16 (7.92) .062 (1.57) MCTH5 90249 101F-3939 402B 402 P-0205 5/16-24 1030-0343, 3/8 (9.53) .125 (3.18) MCTH6 90250 101F-1578 402C 402 P-0215 3/8-24 1010-0344, 9/16 (14.3) .188 (4.78) MCTH960 90251 1010-0883 402E 402 P-0216 9/16-18 1010-0345, 9/16 (14.3) .250 (6.35) MCTH940 90251 101C-7214 402E 402 P-0216 9/16-18 1010-0345, Options: Cutting Oil: P-8784 MCT-SA: Support Arm Assembly Threading tool + (2 x 1/16 Finish Allowance). JsrMka[0'*8 bD_/ZdX&8)"3V 0PyyV3:B7 L bj;, 4wmVcIj[:j8:>BvF:d-|HOLaB3@m02}HIW=Pu/pNC!N-bDC1AS~qk(=nFJ{%#hPvw4)HvsAo6o:! Each kit consists of the required

Model AEGCTM-2 Power Coning-and- Note: Additional blades available for other sizes of tubing. 4 All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold. Please check your registed email for verification. Tighten gland finger-tight.

Outside Diameter Extra Allowance** multiple tools for different size tubing. 1 0 obj Tube Size for Engagement Slip gland and sleeve

3All general terms and conditions of sale, including limitations of our liability, apply to all products and services sold. TUBING. and faster coning. One coning and one threading tool with optional sizes of and slide them onto the tubing before inserting the tubing into 2 0 obj <>stream providing dimensional information associated with a variety Tools, Installation, Operation and Maintenance - Coning, Coning & Threading Kits threading tool for optimum performance with tubing sizes up guide the tool for accurate thread cutting. !$R%,6Rx/6?o7/oMB)Nb"iv8*!a`YZOD:M9mmsocNfCMCp2,O*Z?T/c3_[_

KMCT-HT Coning tool with support arm and reservoir These precision quality manual tools permit on-site end preparation for Parker Autoclave Engineers medium and high pressure tubing installations.

and Maintenance, Tools, Installation, Operation and Maintenance. A properly seated sleeve cannot be displaced Sizes Available: 1/4, 5/16, 3/8 & 9/16 manual threading tool, Autoclave Cone and Threading Machine Tooling & Tooling Kits. All kit items are placed in a hand-carry tool



Sitemap 16