See pressure recommendations in users manual for each spray gun atomizing head. Twist the connection while continuing to push upward until the connector bottoms out on the atomizing head as shown in the fully connected image below. Do not expose air flow control valve and gauges to solvent as damage may occur. All Rights Reserved. 
To reduce the risks associated with chemical exposure: Always wear appropriate personal protective equipment for eye, skin and respiratory protection per the applicable SDS(s) and material container labels at all times when spraying. Always comply with local, state, and national laws and regulations governing ventilation, fire protection, operation, maintenance, and housekeeping. Adjusting the Fluid FlowThe fluid flow can be adjusted by using the fluid needle adjustment knob. Maximum inlet pressure will yield approximately 10 psi (0.69 bar) at the air cap. Manually attach the air flow control valve to the air inlet by hand threading the connection. The versatile selection of replaceable atomizing heads offer like-new spray performance every time. Do not use metal tools to clean the air cap holes as this may scratch them; scratches can distort the spray pattern.
To allow fluid flow, gently turn the fluid needle adjustment knob counter-clockwise 4 full turns. Ensure equipment is cleaned prior to storage. Ensure the equipment you are using with this product is suitable for the use application. Stir as needed. To make a claim under the warranty, you must first contact the 3M Service Center at 1-877-MMMCARS to receive a return authorization number.
Upon validation of the warranty claim, 3M will replace or repair the spray equipment, at 3Ms option, and return it to the purchaser at 3Ms expense, including parts, labor and return shipping charges. The spray gun in the kit is preset in the closed position {pull trigger to verify; there should be minimal fluid needle movement). Description Part Number. While atomizing head locking collar is in the + configuration and without an atomizing head attached to the spray gun body, pull locking collar firmly forward. Inspect for concealed damage and/or missing items. Do not put in gun washer. To flush spray gun, run water or compatible and compliant solvent into the spray gun fluid passage while triggering the spray gun, with fluid tip pointed straight down, until the cleaning fluid appears clear. If it is determined that the claim is not covered by the warranty, the purchaser will be given the option to have the spray equipment repaired outside of the warranty. Spray equipment must be returned, freight prepaid by the purchaser, to the service location address given by the 3M Service Center.
Powered by. Connect pressurized paint or coating supply hose to bottom threaded fitting of pressure fluid hose connector by wrench tightening with two wrenches in the locations shown below. An estimate of parts and labor will be provided by 3M and must be approved by the purchaser in advance. Given the variety of factors that can affect the use and performance of a 3M product, user is solely responsible for evaluating the 3M product and determining whether it is fit for a particular purpose and suitable for users method of application. To reduce the risks associated with tripping, falling and tipping: Route air and liquid hoses and any extension cords away from traffic areas, sharp edges, moving parts and hot surfaces. Slide the atomizing head over the fluid needle and push towards the spray gun body making sure locking collar is in the + configuration with locking lugs at the counter clockwise stop at 3 and 9 oclock. If fasteners were removed for hardware maintenance or accessories, ensure that all fasteners are replaced and tightened before operation. Home 3M 3M 7100228462 Performance Spray Gun System Owners Manual. Read and follow all Safety Statements and Instructions. on 3M 7100228462 Performance Spray Gun System Owners Manual, 3M 7100228462 Performance Spray Gun System, GENERAL SET UP AND SPRAY GUN USE GRAVITY, GENERAL SET UP AND SPRAY GUN USE PRESSURE, Spray Equipment Warranty and Limited Remedy, 3M MA5532 Tempa-Dot Sterile Clinical Disposable Thermometers User Guide, BLACK RIDGE Air Spray Gun Gravity Feed HD Instruction Manual, Vankyo Performance V630W Projector User Manual, IKEA KARLSO Canopy for 3m x 3m Patio Gazebo Single Tier Installation Guide, AJAX 8706 KeyPad Wireless Touch Keyboard User Manual, Meizhou Hongfeng Arts Crafts 266285 BJ 57IN Snowman With Snowflakes Instruction Manual, AJAX 7661 StreetSiren Wireless Outdoor Siren User Manual, AJAX 17938 12V PSU for Hub/Hub Plus/ReX Power Supply Unit User Manual, AJAX 10306 Transmitter Wired to Wireless Detector Converter User Manual, ZERFUN G8 Pro Wireless Microphone System User Manual, Airrex Infrared Heater AH-200/300/800 User Manual, 2017 Toyota Camry Hybrid LE Fuse Box Diagrams, 2017 Mitsubishi Lancer 4WD Fuse Box Diagrams, Mitsubishi Lancer Passenger and Engine Fuse Box Diagram, Mira Honesty ERD Bar Valve and Fittings User Manual. Declared Dual-Number Noise Emission Values according to EN ISO 4871. Next, turn the knob counter-clockwise 2 rotation. - eBay Money Back Guarantee - opens in a new window or tab, - for PayPal Credit, opens in a new window or tab, Learn more about earning points with eBay Mastercard, - eBay Return policy - opens in a new tab or window, - eBay Money Back Guarantee - opens in a new tab or window. To reduce the risks associated with chemical exposure and hazardous pressure: Do not use this product around unsupervised children. Remove retention pin from pressure fluidhose connector bracket. Never point a spray gun at anyone else or place any part of your body in front of the spray gun. {"modules":["unloadOptimization","bandwidthDetection"],"unloadOptimization":{"browsers":{"Firefox":true,"Chrome":true}},"bandwidthDetection":{"url":"https://ir.ebaystatic.com/cr/v/c1/thirtysevens.jpg","maxViews":4,"imgSize":37,"expiry":300000,"timeout":250}}, Add to cart to save with this special offer. Adjusting the Fan Pattern SizeThe fan size is regulated by the fan adjustment knob. Comment document.getElementById("comment").setAttribute("id","a927b9bbc5fac453973ba2523bb195fb");document.getElementById("afe6277d1c").setAttribute("id","comment"); Save my name, email, and website in this browser for the next time I comment. NOTICE: USPS TRANSIT TIMES MAY BE LONGER THAN USUAL! Ensure you are familiar with the controls, functionality, and proper use of the equipment. Rotate the locking collar counter-clockwise. Do not use any cleaning method which may allow solvent into the spray gun air passages.Do not expose air flow control valve and gauges to solvent as damage may occur. NOTE: The sum of a measured noise emission value and its associated uncertainty represents an upper bound of the range of values which can occur in the measurements. Retain these instructions for future reference. Limitation of Liability: Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product, whether direct, indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability. Attach spray gun to filled 3M PPS Series 2.0 Spray Cup System cup. Locking Collar RemovalIf desired, the atomizing head locking collar can be removed from gun frame in order to thoroughly clean head of gun body. [Note: This may include grounding with shoes, heel straps, and static conductive (or static dissipative) gloves.]. 3M Accuspray ONE Replacement Spray Gun Kit, 3M Accuspray Atomizing Head Re ll Kit, 2.0 mm, 3M Accuspray Atomizing Head Re ll Kit, 1.8 mm, 3M Accuspray Atomizing Head Re ll Kit, 1.4 mm, 3M Accuspray Atomizing Head Re ll Kit, 1.3 mm, 3M Accuspray Atomizing Head Re ll Kit, 1.2 mm, Remove atomizing head and reattach in gunbody and listen, Replace gun: Call 1-877-MMM-CARS or(1-877-666-2277), Pressure feed hvlp & lvlp spray gun (34 pages), Performance spray gun hvlp - gravity, maximum operating pressure: 20 psi, 1.38 bar (2 pages), Manual will be automatically added to "My Manuals", Paint Sprayer 3M Accuspray HGP Spray Gun Owner's Manual, Paint Sprayer 3M Accuspray 16580 Owner's Manual, Paint Sprayer 3M Accuspray Owner's Manual, Paint Sprayer 3M 16212 Instruction Manual, Paint Sprayer 3M Performance Spray Gun Owner's Manual, Paint Sprayer 3M PPS 16121 Instruction Manual, Paint Sprayer 3M Series 05 Owner's Manual, Paint Sprayer 3M PPS 2.0 Series Quick Start Manual, Paint Sprayer 3M Series 52 Owner's Manual, Paint Sprayer 3M Scotchkote HSS-450 User Instructions, Accuspray 16580 Replacement Parts And Accessories, Performance Spray Gun Replacement Parts And Accessories, Accuspray HGP Spray Gun Replacement Parts And Accessories, Accuspray Replacement Parts And Accessories, Series 52 Spray Gun Parts Identification Series 52. Fine tuning of these adjustments will be based on your material and technique. Do not use any cleaning method which may allow solvent into the spray gun air passages. To retain unused paint or temporarily store mixed material, see your Local, State, Federal and OSHA guidelines, along with paint manufacturers recommendations for storage. Intended Use:This Spray Gun Kit is intended to provide the means to apply liquid coatings via a spraying process. Release Pressure from paint or coatings supply hose. Relieve the air and fluid pressure from the spray gun and cup before servicing. Slide bracket over air inlet fitting within slotted track in the same direction atomizing heads slide on to gun frame. Solvent left in the spray gun air passages could result in a poor-quality paint finish. Solvent left in the spray gun air passages could result in a poor quality coating finish. INTERNATIONAL PRICING MAY VARY. Ensure equipment is stored indoors at room temperature. These adjustment procedures will serve only as a starting point. Directly connect your 3M Performance Spray gun to the 3M PPS Series 2.0 Spray Cup System. Do not expose air flow control valve and gauges to solvent as damage may occur. Painters needed a cleaner, faster, more efficient method of mixing and applying paint. The spray gun in the kit is preset in the closed position (pull trigger to verify; there should be minimal fluid needle movement). 3M invented the first disposable paint cup system nearly 20 years ago-the 3M PPS Paint Preparation System. Accuspray 3M Rebuild Kit Genuine Replacement Part 97-236 For 05-300 Gun. PPS 0.9 #6 1.1 #9 1.5 1 per case, 3M 39-Pro1 Series 39 System 12s 2 qt dual regs 0.9 1.3 5 8 Obsolete, 3M 39-Pro2 Series 39 System 12s 2 qt dual regs 1.1 1.5 7 9 Obsolete, 3M Accuspray Atomizing Head 16611 1.8 mm 4 per kit 6 kits per case, 3M Accuspray Atomizing Head 16612 1.4 mm 4 atomizing heads per kit 6 kits per case, 3M Accuspray Atomizing Head 16609 2.0 mm Red Opaque 4 atomizing heads per kit 6 kits per case, 3M Accuspray Air Flow Control Valve 16573 1 per case, 3M Accuspray 12S-Pro9 HVLP Spray Gun No Cup No Reg1.8 #10 Composite Cap 1 per case, 3M Accuspray Atomizing Head 16584 Orange 1.4 mm 1 atomizing heads per each 10 each per case, 3M Accuspray Atomizing Head 16585 Clear Transparent 1.8 mm 1 atomizing heads per each 10 each per case, 3M Accuspray AAH Air Cap Tester 16565 1 per case, 3M Accuspray Atomizing Head16582 Blue 1.2 mm 1 atomizing heads per each 10 each per case, 3M Accuspray Atomizing Head16583 Green 1.3 mm 1 atomizing heads per each 10 each per case, 3M Accuspray Atomizing Head16614 Green 1.3 mm 4 atomizing heads per kit 6 kits per case, 3M Accuspray Atomizing Head Refill Pack for 3M PPS Series 2.0 26620 Red 2.0 mm 4 nozzle per pack 6 packs per case, 3M Accuspray Atomizing Head Refill Pack for 3M PPS Series 2.0 26618 Clear 1.8 mm 4 nozzles per pack 6 packs per case, 3M Accuspray Atomizing Head Refill Pack for 3M PPS Series 2.0 26585 Clear 1.8 mm 5 per case.
Periodically, lubricate moving components such as the fluid needle, fan adjustment threads, fluid needle adjustment threads and spring. The spray pattern can be changed from vertical to horizontal by rotating the air cap a 1/4 turn. To reduce the risks associated with bursting and chemical exposure: Do not operate spray gun system without a functional inlet pressure gauge. Insert the 3M PPS Series 2.0 Spray Cup System disposable liner into the 3M PPS Series 2.0 Spray Cup System mixing cup. Example of attaching air flow control valve: Setting the Air PressureGravity: For optimum spray performance, pull trigger back and adjust operating pressure to read 20 psi {1.38 bar) for the 1.2, 1.3, 1.4, 1.6, 1.8 and 2.0 atomizing heads.Note: When operating this unit, use only undamaged, suitably solvent-resistant and appropriately pressure-rated static-conductive air hoses. Disconnect pressurized paint or coating supply hose from bottom threaded fitting of the pressure fluid hose connector by wrench loosening with two wrenches in the locations shown below. Reinvented from top to bottom, the 3M PPS 2.0 Spray Cup system delivers the next evolution of the 3M PPS painting revolution. Re-attach retention pin into pressure fluid hose connector bracket holes. To allow fluid flow, gently turn the fluid needle adjustment knob counter-clockwise 4 full turns. Consult applicable SDS(s) and material container labels for each material being sprayed in the work area. Product material compatibility information available upon request. These adjustment procedures will serve only as a starting point. SAFETY INFORMATIONPlease read, understand, and follow all safety information contained in these instructions prior to the use of this Spray Gun Kit. 3M 23K Turbine Pkg 23K-Pro1 Std. The code of P affixed to this product indicates that the product in question has the designation of machinery, designation of series or type, and manufacturers address identified in this documentation, in compliance with the Machinery Directive 2006/42/EC. This Spray Gun Kit is used in automotive, industrial, and consumer finishing applications. NOTICE: USPS TRANSIT TIMES MAY BE LONGER THAN USUAL! See manual for appropriate cleaning process. A-WEIGHTED EMISSION SOUND PRESSURE LEVEL AT THE WORKSTATION: Measured value: LpA = 72,9 dB(A) (ref 20Pa), Measured value: LWA = 80,1 dB(A) (ref 1 pW}, Values determined according to noise test code EN 14462 using the basic standards, 3M PPS Series 2.0 Spray Cup System Standard Size Mixing Cup, 3M PPS Series 2.0 Spray Cup System Standard Size Lids and Liners, 3M PPS Series 2.0 Spray Cup System Sealing Plugs, 1.2 3M Performance Gravity HVLP Atomizing Head, 1.3 3M Performance Gravity HVLP Atomizing Head, 1.4 3M Performance Gravity HVLP Atomizing Head, 1.6 3M Performance Gravity HVLP Atomizing Head, 1.8 3M Performance Gravity HVLP Atomizing Head, 2.0 3M Performance Gravity HVLP Atomizing Head, 1.1 3M Performance Pressure HVLP Atomizing Head, 1.4 3M Performance Pressure HVLP Atomizing Head, 1.8 3M Performance Pressure HVLP Atomizing Head. Atomizing heads connect directly to 3M PPS Series 2.0 Spray Cup System. Seller assumes all responsibility for this listing. Dispose of device components in accordance with local laws and regulations. PPS 1.3 #705 1.8 #707 1 per case, 3M 240K Turbine Pkg 240K-Pro1 Std. To reduce the risks associated with fire and explosion: Ensure VOC concentration is kept below ignition threshold per liquid coating material SDS(s). Fine tuning these adjustments will be based on your of material and technique.
WARNING: Indicates a hazardous situation which, if not avoided, could result in serious injury or deathCAUTION: Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury and/or property damage.NOTICE: Indicates a hazardous situation which, if not avoided, could result in property damage only.
Pull the atomizing head away from the gun body to remove.
Always follow required air and liquid pressure relief procedures for relieving air and liquid pressure from the spray equipment. Repair/replace worn, damaged or malfunctioning components with 3M approved components. Attaching Pressure Fluid Hose Connector to Gun, Fluid Hose to Atomizing Head Connection & Disconnection, Removing the Pressure Fluid Hose Connector from Gun. 2. To reduce the risks associated with impact: Always inspect to ensure that the atomizing head is properly attached and secure. Slide connection over the spout of the atomizing head and push the connection onto the atomizing head. Your 3M Performance Spray Gun Kit could include one or more of the following, depending on the kit that was purchased: 3M Performance Spray GunThe 3M Performance Spray Gun is designed for use with a compressed air system, featuring a composite* spray gun body requiring 13 scfm (370.5 L/min) and a 1/4 (1/4 BSP) air inlet. If you discover any damage and/or missing pieces, contact your distributor immediately. To reduce the risks associated with chemical exposure, hazardous pressure and impact: Do not maintain or service the spray gun other than as instructed in the users manual. Attaching Air Fitting or Regulating Equipment. Use in any other application has not been evaluated by 3M and may lead to an unsafe condition. To reduce the risks associated with hazardous noise: Always wear hearing protectors when you are exposed to noise. Pour material to be sprayed into the 3MPPS Series 2.0 Spray Cup System mixing cup.
Turn until tight. Many factors beyond 3Ms control and uniquely within users knowledge and control can affect the use and performance of a 3M product in a particular application. Use one wrench to connect the air flow control valve. Do not use any cleaning method which may allow solvent into the spray gun air passages. Reverse process to re-attach locking collar ensuring that the retention bumps on the ID align with spray gun body head protrusions. Solvent left in the spray gun air passages could result in a poor-quality paint finish. All ignition sources such as smoking or electrical devices must be kept out of the spray area. It is expected that all users be fully trained in the safe operation of this Spray Gun Kit. 3M Performance Spray Guns are engineered for performance. BLACK RIDGE Air Spray Gun Gravity Feed WARRANTY: Our product is guaranteed to be free from quality and, Voyager Owner Handbook - Download [optimized] Voyager Owner Handbook - Download, IKEA KARLSO Canopy for 3m x 3m Patio Gazebo Single Tier Safety Instructions As floor materials vary, screws. View cart for details. Adjusting the Fluid FlowThe fluid flow can be adjusted by using the fluid needle adjustment knob. Before use check spray equipment for damage and proper function. Adding the 3M PPS Series 2.0 Spray Cup System Components. Copyright 1995-2022 eBay Inc. All Rights Reserved. If you'd like to get the additional items you've selected to qualify for this offer. It will be necessary to connect an air fitting, an air regulator or air flow control valve to the air inlet located at the base of the spray gun body. Place the 3M PPS Series 2.0 Spray Cup System lid with built-in filter on top of the 3M PPS mixing cup with liner and snap into place. Maximum inlet pressure with full trigger pull**, Gravity Atomizing Heads: 1.2, 1.3, 1.4, 1.6, 1.8, 2.0 = 20 psi (1.38 bar)Pressure Atomizing Heads: 1.1, 1.4, 1.8 = 18 psi (1.24 bar). The minimum allowed order amount is $30.00. Do not pull on air hoses to move the compressor. Note: Complete steps below before connecting spray gun to air source. Do not leave immersed in cleaning solvents. Except as written above, 3M MAKES NO OTHER WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. Secure the atomizing head by rotating the retainer ring, clockwise until the retainer ring tabs are locked in the X configuration. Never perform unapproved modifications or maintenance on this product. 3M Performance Pressure HVLP Atomizing Head Refill Kit, 1.1 26811, 3M Performance Pressure HVLP Atomizing Head Refill Kit, 1.4 26814, 3M Performance Pressure HVLP Atomizing Head Refill Kit, 1.8 26818, 3M Performance Pressure HVLP Atomizing Head Variety Refill Kit 26830, 3M Performance Gravity HVLP Atomizing Head Refill Kit, 1.2 26712, 3M Performance Gravity HVLP Atomizing Head Refill Kit, 1.3 26713, 3M Performance Gravity HVLP Atomizing Head Refill Kit, 1.4 26714, 3M Performance Gravity HVLP Atomizing Head Refill Kit, 1.6 26716, 3M Performance Gravity HVLP Atomizing Head Refill Kit, 1.8 26718, 3M Performance Gravity HVLP Atomizing Head Refill Kit, 2.0 26720, 3M Performance Gravity HVLP Atomizing Head Variety Refill Kit 26730, 3M Performance Spray Gun 26832, 3M Performance Spray Gun Needle 26838, 3M Performance Spray Gun Pressure Whip 26833, 3M Performance Spray Gun Pin 26834, 3M Performance Spray Gun Gravity HVLP Test Air Cap 26736, 3M Performance Spray Gun Pressure HVLP Test Air Cap 26836, 3M Performance Spray Gun Rebuild Kit 26840, 3M Performance Spray Gun Locking Collar 26835, 3M Accuspray Regulator and Air Flow Control Valve 16573, 3M Performance Spray Gun H/O Conversion Pack 26837, 3M Performance Spray Gun Ball Valve 26839, 3M High Power Spray Gun Cleaner 26689, 3M PPS Series 2.0 Spray Cup System Kit(*additional sizes available) 26000. With atomizing head securely locked on frame, align connector wings parallel to needle or front-to-back. 3M reserves the right to make changes at any time without notice. Your email address will not be published. To reduce the risks associated with sharp points: Do not touch the sharp end of the fluid needle when exposed and handle fluid needles carefully during replacement. To reduce the risks associated with muscles strain: Avoid using spray equipment continuously without taking occasional breaks. Users are expected to comply with local regulations for working in explosive environments and any requirements for the material to be sprayed (consult material SDS) and use appropriate PPE for both. Values measured in a particular work place may be higher than the declared values. Something went wrong. Always maintain a readily available, approved fire extinguisher or other approved fire fighting equipment in or near the spray area. Any misuse of the equipment or accessories, such as over pressurizing, modifying parts, using incompatible chemicals and fluids, or using worn or damaged parts can cause serious bodily injury, fire, explosion or property damage. To reduce the risks associated with chemical exposure, hazardous pressure, fire/explosion, or environmental contamination: Read, understand and follow all safety statements in applicable equipment users manuals to avoid possible safety hazards. Remove retention pin from connector bracket holes. If you Buy It Now, you'll only be purchasing this item. Twist the connection while gently pulling downward. Note: Do Not Put In Gun Washer. Refresh your browser window to try again.
The spray gun in the kit is preset in the closed position (gently turn the fan adjustment knob clockwise to verify; knob should not move). The fan adjustment will allow you to spray from a small round to a full fan pattern. UnpackingRemove the components from the box. The lightweight, impact resistant gun body features a newly designed locking collar that allows for quick atomizing head changes for an easy switch between paints or coatings and cleanup. Read, understand and follow all safety statements as well as wear appropriate, approved personal protective equipment per the applicable SDS and material container labels for cleaning solutions. 3M 2020 3M and PPS are trademarks of 3M Company, used under license in Canada. PPS 0.9 #6 1.1 #9 1.5 1 per case, 3M 240C Turb/Comp Pkg 240C-Pro1 2 Qt 0.9 #6 1.1 #9 1.5 1 per case, 3M 240G Turbine Pkg 240G-Pro1 Std. MIcro Parts & Supplies, Inc. 2022. 3M warrants to the original purchaser that, when used in accordance with 3Ms written instructions, 3M spray equipment will be free of defects in materials and manufacture for one year from the date of purchase. When operating this unit, use only undamaged suitably solvent-resistant and appropriately pressure-rated static-conductive air hoses. Hazards can occur from equipment misuse. Adjust to fit the air flow valve nut, then tighten the connection. Consult your work environment and local regulations regarding use personal protective hearing protection.
- Michael Kors Saffiano Leather Tote
- Long Sleeve Striped Shirt Plus Size
- Marvel Legends Clearance Uk
- Art Institute Of Houston Locations
- Solid Fit & Flare Dress Without Bag
- Boys Ties Near Wiesbaden
- Dogwood Memorial Tree
- Jet Air Filtration System Replacement Filters
- Stainless Steel Pipe Properties
- Zeolite Detox Benefits
- Dr Dennis Gross Alpha Beta Cleanser
- Vita Spa Replacement Parts
- Aurora University Dorm Costs